added i2c controller functions, added IDE interface functions, fiexd IDE schematics
This commit is contained in:
Dennis Gunia
327
OperatingSystem/software/test_iic.asm
Normal file
327
OperatingSystem/software/test_iic.asm
Normal file
@@ -0,0 +1,327 @@
|
||||
.include "extern_symbols.s" ;include monitor symbols.
|
||||
org 0xB000
|
||||
CS_PIO_BD .EQU 0xF5
|
||||
CS_PIO_BC .EQU 0xF7
|
||||
CS_PIO_AD .EQU 0xF4
|
||||
CS_PIO_AC .EQU 0xF6
|
||||
|
||||
CS_I2C_S1 .EQU 0xF3
|
||||
CS_I2C_SX .EQU 0xF2
|
||||
|
||||
IIC_RTC equ 11010000b
|
||||
|
||||
IIC_INIT:
|
||||
LD A,0xCF
|
||||
OUT (CS_PIO_AC), A
|
||||
LD A,11110101b
|
||||
OUT (CS_PIO_AC), A
|
||||
|
||||
LD A,00000000b ; Reset PCF8584 minimum 30 clock cycles
|
||||
OUT (CS_PIO_AD), A
|
||||
LD BC,0x1000
|
||||
CALL PAUSE_LOOP
|
||||
LD A,0000010b
|
||||
OUT (CS_PIO_AD), A
|
||||
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
|
||||
LD A, 0x80 ;S1 -> Select S0, PIN disabled, ESO = 0, Interrupt disabled, STA, STA, ACK = 0
|
||||
OUT (CS_I2C_S1),A
|
||||
CALL SlowAccess
|
||||
CALL SlowAccess
|
||||
|
||||
LD A,0x55 ;S0 -> Loads byte 55H into register S0'; effective own address becomes AAH
|
||||
OUT (CS_I2C_SX),A
|
||||
CALL SlowAccess
|
||||
|
||||
LD A, 0xA0 ;S1 -> Loads byte A0H into register S1, i.e. next byte will be loaded into the clock control register S2.
|
||||
OUT (CS_I2C_S1),A
|
||||
CALL SlowAccess
|
||||
|
||||
|
||||
LD A,0x00 ;Load 18H into S2 register (clock control - 8 MHz, 90 KHz)
|
||||
OUT (CS_I2C_SX),A
|
||||
CALL SlowAccess
|
||||
|
||||
LD A,0xC1 ;S1 -> loads byte C1H into register S1; register enable
|
||||
;serial interface, set I 2C-bus into idle mode;
|
||||
;SDA and SCL are HIGH. The next write or read
|
||||
;operation will be to/from data transfer register
|
||||
;S0 if A0 = LOW.;
|
||||
OUT (CS_I2C_S1),A
|
||||
CALL SlowAccess
|
||||
|
||||
|
||||
|
||||
;CALL force_stop
|
||||
JP PROMPT_BEGIN
|
||||
|
||||
LD BC,$0100
|
||||
CALL PAUSE_LOOP
|
||||
|
||||
|
||||
; Send test message to RTC
|
||||
|
||||
LD DE, 0xC000 ; Set I2C Buffer Location
|
||||
LD A,0x00
|
||||
LD (DE),A
|
||||
;call regdump
|
||||
|
||||
LD B, IIC_RTC ; Set I2C Address
|
||||
LD A, 1 ; Set I2C Buffer length
|
||||
call i2c_send
|
||||
|
||||
LD DE, 0xC010
|
||||
LD B, IIC_RTC
|
||||
LD A, 7
|
||||
call i2c_read
|
||||
|
||||
|
||||
|
||||
JP PROMPT_BEGIN
|
||||
|
||||
|
||||
;CLK_ENABLE:
|
||||
; LD DE, 0xC000 ; Set I2C Buffer Location
|
||||
; LD A,0x00
|
||||
; LD (0xC000),A
|
||||
; LD (0xC001),A
|
||||
; ;call regdump
|
||||
;
|
||||
; LD B, IIC_RTC ; Set I2C Address
|
||||
; LD A, 2 ; Set I2C Buffer length
|
||||
; call i2c_send
|
||||
; JP PROMPT_BEGIN
|
||||
|
||||
;------------------------------------------------------------------------------
|
||||
; i2c_send
|
||||
;
|
||||
; Sends data over the i2c bus
|
||||
; A contains BYTE COUNTER
|
||||
; B contains ADDRESS
|
||||
; DE contains location of Data Buffer
|
||||
;------------------------------------------------------------------------------
|
||||
i2c_send:
|
||||
; CALL PRINTINLINE;
|
||||
; defb "SEND A",10,13,0
|
||||
PUSH BC
|
||||
PUSH AF
|
||||
CALL i2c_bus_rdy
|
||||
; CALL PRINTINLINE
|
||||
; defb "SEND START",10,13,0
|
||||
LD A,B ;Load 'slave address' into S0 register:
|
||||
OUT (CS_I2C_SX),A
|
||||
CALL SlowAccess
|
||||
|
||||
LD A, 0xC5 ;Load C5H into S1. 'C5H' = PCF8584 generates
|
||||
;the 'START' condition and clocks out the slave
|
||||
;address and the clock pulse for slave acknowledgement.
|
||||
OUT (CS_I2C_S1),A
|
||||
POP AF
|
||||
LD C,A
|
||||
INC C
|
||||
i2c_send_1: ; LOOP 1 : Wait for bus ready
|
||||
IN A,(CS_I2C_S1) ; Read byte from S1 register
|
||||
BIT 7,A ; Is bus free? (S1 ~BB=1?)
|
||||
JR NZ,i2c_send_1 ; No - loop
|
||||
BIT 4,A ; slave acknowledged? (LRB = 0?)
|
||||
JR NZ, i2c_send_stop ; if not, cancel transmission
|
||||
LD A,(DE) ; Load next byte from buffer
|
||||
INC DE
|
||||
DEC C
|
||||
JR Z, i2c_send_stop ; if counter = 0, exit loop
|
||||
OUT (CS_I2C_SX),A ; Send byte
|
||||
JR i2c_send_1 ; if counter > 0, loop again
|
||||
i2c_send_stop:
|
||||
LD A, 0xC3 ;STOP
|
||||
OUT (CS_I2C_S1),A
|
||||
CALL SlowAccess
|
||||
POP BC
|
||||
RET
|
||||
|
||||
|
||||
;------------------------------------------------------------------------------
|
||||
; i2c_read
|
||||
;
|
||||
; Sends data over the i2c bus
|
||||
; A contains BYTE COUNTER
|
||||
; B contains ADDRESS
|
||||
; DE contains location of Data Buffer
|
||||
;------------------------------------------------------------------------------
|
||||
i2c_read:
|
||||
PUSH DE
|
||||
PUSH BC
|
||||
PUSH AF
|
||||
LD A,B ;Load 'slave address' into S0 register:
|
||||
OR 0x01 ;Set RW Bit for read operation
|
||||
OUT (CS_I2C_SX),A
|
||||
CALL SlowAccess
|
||||
CALL i2c_bus_rdy ; Is bus ready
|
||||
LD A, 0xC5 ;Load C5H into S1. 'C5H' = PCF8584 generates
|
||||
;the 'START' condition and clocks out the slave
|
||||
;address and the clock pulse for slave acknowledgement.
|
||||
OUT (CS_I2C_S1),A
|
||||
;Setup counter
|
||||
POP AF
|
||||
LD C,A ; Load BYTE COUNTER into C
|
||||
INC C ; Offset C by 1
|
||||
i2c_read_1: ;Wait for PIN = 0
|
||||
IN A,(CS_I2C_S1) ; Read byte from S1 register
|
||||
BIT 7,A ; S1 PIN=1?
|
||||
JR NZ,i2c_read_1 ; No - loop
|
||||
BIT 3,A ; S1 LRB=0? slave ACK?
|
||||
JR NZ, i2c_read_error ; No ACK -> an error has occured
|
||||
DEC C
|
||||
LD A, C
|
||||
DEC A ;If n = m − 1?
|
||||
JR Z, i2c_read_last
|
||||
IN A,(CS_I2C_SX)
|
||||
LD (DE),A
|
||||
INC DE
|
||||
JR i2c_read_1
|
||||
i2c_read_last: ;read last byte
|
||||
LD A, 0x40
|
||||
OUT (CS_I2C_S1),A
|
||||
CALL SlowAccess
|
||||
IN A,(CS_I2C_SX) ;receives the final data byte. Neg. ACK is also sent.
|
||||
LD (DE),A
|
||||
INC DE
|
||||
i2c_read_last_1:
|
||||
IN A,(CS_I2C_S1) ; Read byte from S1 register
|
||||
BIT 7,A ; S1 PIN=1?
|
||||
JR NZ,i2c_read_last_1 ; No - loop
|
||||
|
||||
i2c_read_error:
|
||||
NOP
|
||||
i2c_read_stop:
|
||||
LD A, 0xC3
|
||||
OUT (CS_I2C_S1),A
|
||||
CALL SlowAccess
|
||||
IN A,(CS_I2C_SX) ;transfers the final data byte from the
|
||||
;data buffer to accumulator.
|
||||
CALL SlowAccess
|
||||
LD (DE),A
|
||||
POP BC
|
||||
POP DE
|
||||
RET
|
||||
|
||||
|
||||
i2c_stop_force:
|
||||
|
||||
;------------------------------------------------------------------------------
|
||||
; i2c_rdy
|
||||
;
|
||||
; Waits until the PCF8584 signals a byte transmission/reception is complete.
|
||||
;------------------------------------------------------------------------------
|
||||
i2c_rdy:
|
||||
PUSH AF
|
||||
i2c_rlp:
|
||||
IN A,(CS_I2C_S1) ; Read byte from S1 register
|
||||
BIT 7,A ; Is Tx/Rx complete? (S1 PIN=0?)
|
||||
call print_a_hex
|
||||
JR NZ,i2c_rlp ; No - loop
|
||||
i2crlpex:
|
||||
POP AF
|
||||
RET
|
||||
|
||||
;------------------------------------------------------------------------------
|
||||
; i2c_bus_rdy
|
||||
;
|
||||
; Waits until the I2C bus is free before RETurning
|
||||
;------------------------------------------------------------------------------
|
||||
i2c_bus_rdy:
|
||||
PUSH AF
|
||||
i2c_blp:
|
||||
IN A,(CS_I2C_S1) ; Read byte from S1 register
|
||||
PUSH AF
|
||||
call print_a_hex
|
||||
POP AF
|
||||
BIT 0,A ; Is bus free? (S1 ~BB=1?)
|
||||
JR Z,i2c_blp ; No - loop
|
||||
i2cblpex:
|
||||
POP AF
|
||||
RET
|
||||
|
||||
;------------------------------------------------------------------------------
|
||||
; PAUSE_LOOP
|
||||
;
|
||||
; Timer function
|
||||
;
|
||||
; 16-bit (BC) decrement counter, performing 4xNEG loop until BC
|
||||
; reaches zero.
|
||||
;
|
||||
; 61 T-states in loop = 15.25uS per loop @ 4 MHz - near enough
|
||||
; a second delay for 65,535 iterations.
|
||||
;
|
||||
; Set iteration count in BC before calling this function.
|
||||
; Destroys: BC
|
||||
;------------------------------------------------------------------------------
|
||||
PAUSE_LOOP:
|
||||
PUSH AF ; 11 T-states
|
||||
pau_lp:
|
||||
;NEG ; 8 T-states
|
||||
;NEG ; 8 T-states
|
||||
;NEG ; 8 T-states
|
||||
;NEG ; 8 T-states
|
||||
PUSH BC ; 11 T-states
|
||||
POP BC ; 10 T-states
|
||||
PUSH BC ; 11 T-states
|
||||
POP BC ; 10 T-states
|
||||
DEC BC ; 6 T-states
|
||||
LD A,C ; 9 T-states
|
||||
OR B ; 4 T-states
|
||||
JP NZ,pau_lp ; 10 T-states
|
||||
POP AF ; 10 T-states
|
||||
RET ; Pause complete, RETurn
|
||||
|
||||
;------------------------------------------------------------------------------
|
||||
; PRINTINLINE
|
||||
;
|
||||
; String output function
|
||||
;
|
||||
; Prints in-line data (bytes immediately following the PRINTINLINE call)
|
||||
; until a string terminator is encountered (0 - null char).
|
||||
;------------------------------------------------------------------------------
|
||||
PRINTINLINE:
|
||||
EX (SP),HL ; PUSH HL and put RET ADDress into HL
|
||||
PUSH AF
|
||||
PUSH BC
|
||||
nxtILC:
|
||||
LD A,(HL)
|
||||
CP 0
|
||||
JR Z,endPrint
|
||||
CALL print_char
|
||||
INC HL
|
||||
JR nxtILC
|
||||
endPrint:
|
||||
INC HL ; Get past "null" terminator
|
||||
POP BC
|
||||
POP AF
|
||||
EX (SP),HL ; PUSH new RET ADDress on stack and restore HL
|
||||
RET
|
||||
|
||||
SlowAccess:
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
NOP
|
||||
RET
|
||||
|
||||
|
||||
;.include "regdump.s"
|
||||
|
||||
force_stop:
|
||||
IN A,(CS_I2C_S1)
|
||||
BIT 0, A
|
||||
RET NZ
|
||||
LD A, 11000011b
|
||||
OUT (CS_I2C_S1),A
|
||||
NOP
|
||||
NOP
|
||||
JR force_stop
|
||||
Reference in New Issue
Block a user